Software Board

Topic	Replies	Created	Last reply
Final Version of AXON 3???	8	by AntonioJose81 2013-03-22 09:15	by toranarod 2013-03-30 06:59
Axon 3.0 alpha 1 released [Page 1, 2]	60	by Andrew 2012-10-19 13:37	by waltorg 2013-03-26 23:59
G-Code-Optimizer for AXON	1	by Bundes-Metal-Mi... 2013-03-20 13:45	by AntonioJose81 2013-03-22 09:05
Will Axon 3 be available for Rapman 3.1?	2	by cinmay 2012-12-03 17:39	by wombatmorrison 2013-03-11 18:25
Blank Board	3	by lafs1218 2013-03-08 15:04	by Aaron Technical 2013-03-11 07:31
skeinforge software issues	0	by hoelzle2 2013-03-02 21:35	n/a
Too bad I bougth this 3d printer.	1	by zolm 2013-03-01 19:39	by speed 2013-03-02 00:30
PRINTING FROM A COMPUTER??	3	by REZTECH 2013-02-21 21:00	by ttelmah 2013-03-01 05:03
Axon 2.1 released.. 21 Sept 2012	23	by Dave White 2012-09-21 16:11	by evschneider 2013-02-24 17:24
Restoring settings after firmware update	1	by KevE 2013-01-30 12:09	by NMRC 2013-02-20 10:47
Raft prints - second material doesn't heat before it attempts to print	6	by Harry 2012-02-22 20:37	by muqtada321 2013-02-20 04:48
AXON 3 - PLA 250°C ??!!??	2	by daniel303 2013-01-11 07:57	by PSwage3D 2013-02-13 15:32
rapman 3.2 stops after each layer, and spoils lots of ABS after update.	1	by Martijn332 2012-12-09 17:40	by Daemon 2013-02-12 18:14
material cost	0	by creighta 2013-02-07 16:07	n/a
Dem bones	13	by Forrest Higgs 2010-09-26 13:25	by johnmakesdc 2013-02-07 04:06
Axon 3	11	by visionnt 2012-12-20 05:52	by speed 2013-02-06 00:31
Axon 3 crashes	3	by Naty 2012-12-13 02:48	by Scott Barbour 2013-02-01 16:03
Valid G-codes list	2	by [email protected] 2013-01-31 07:43	by [email protected] 2013-02-01 03:32
Need to Reprocess Calibration File to Work With Our Custom Machine Settings for PLA	0	by Claudster 2013-01-29 09:54	n/a
Speed Setting Built into Firmware!!	3	by Ryan Thomas 2012-11-19 10:24	by unfold 2013-01-24 15:43
Converting from a Rap Man to a BFB 3000	1	by Robert F 2012-10-08 21:44	by PhilipSA 2013-01-19 03:39
Firmware upgrade installer does not see printer	2	by cantieny 2013-01-16 13:00	by gyrogearloose 2013-01-18 03:43
axon 3 part no good	0	by stollah 2013-01-16 08:28	n/a
Opening an STL file to make changes	2	by joestefano 2013-01-09 21:56	by mlehtola 2013-01-12 08:07
Axon 2.0 has suddenly started generating rafts below the build platten!! (on a rapman 3.1)	2	by geoffwhite 2012-11-16 11:07	by markporter 2013-01-10 15:13